Packaging and installation requirements for spiral steel pipes

Packaging of spiral steel pipe (SSAW pipe)

1. Spiral steel pipe packaging should be able to avoid loosening and damage during normal loading, unloading, transportation and storage.

2. If the buyer has special requirements for the packaging materials and methods of spiral steel pipes, it should be specified in the contract. If not specified, the packaging material and packaging method are optional by the supplier.

3. Packaging materials should comply with relevant regulations. If there is no requirement for packaging materials, they should meet the intended purpose and avoid waste and environmental pollution.

4. If the customer requires that the spiral steel pipes not have damage such as bumps on the outside, it can be considered to use a protective device between the spiral steel pipes. The protective device can use rubber, straw rope, fiber cloth, plastic, pipe cap and so on.

5. Thin-walled spiral steel pipes can be protected by internal support or external frame protection due to their thick walls and thin walls. The material of the bracket and the outer frame adopts the same steel material as the spiral steel pipe.

6. The state stipulates that the spiral steel pipes shall be packed in bulk. If the customer requires bundling, it can be considered as appropriate, but the caliber must be between 159MM and 500MM. The bundled materials are packed and fastened with steel belts, and each strand should be twisted into at least two strands, and should be appropriately increased according to the outer diameter and weight of the spiral steel pipe to prevent loosening.

7. The fixed-length spiral steel pipe may not be bundled.

8. If there are threaded buckles at both ends of the spiral steel pipe, it should be protected by a thread protector. Apply lubricating oil or anti-rust agent to the threaded fasteners. Both ends of the spiral steel pipe are breached, and nozzle protectors can be added at both ends according to requirements.

9. If the spiral steel pipe is put into the container, the container should be covered with soft moisture-proof devices such as textile cloth and straw mat. In order to scatter the spiral steel pipe in the container, it can be bundled or welded with protective brackets outside the spiral steel pipe, etc.

Installation and use of spiral steel pipe

After the spiral steel pipe is transported to the destination, there are strict technical requirements for the installation and use of the spiral steel pipe, which must be carried out according to the actual situation and the operating procedures to ensure safety and quality. In the general use process, the spiral steel pipe needs to pay attention to the following points

1. Construction preparation before use of spiral steel pipe

Pipeline trenches should be dug well, and pipe wells should be built well. All kinds of spiral steel pipes and tools needed, including welding machines, cutting machines, electric hammers, polishing machines, etc., must be fully prepared. Only after a series of preparations can the installation begin.

2. Installation of spiral steel pipe

According to the drawing design, prefabricate the pipe support according to the site conditions, then punch out according to the design and site, then polish the groove with a polishing machine, and then weld it.

3. Use quality requirements

(1) The vertical installation deviation of the riser should be less than 3 mm per meter, and the horizontal installation deviation should be less than 1 mm.

(2) The branch pipe should not be welded at the weld, and welding should be avoided at the bend.

(3) The welding must be straight, the weld seam is complete, and the surface of the weld seam has no burn-through and cracks.

https://www.steelweldedpipe.com/news/packaging-and-installation-requirements-for-spiral-steel-pipes-138496.html

评论

发表评论

此博客中的热门博文

The main reason for the porosity of submerged arc welding seam

 Submerged arc welding technology is the welding process of SSAW steel pipe and LSAW steel pipe. During the welding process, in addition to insufficient penetration, burn-through and poor formation caused by improper welding process parameters, there will also be pores, slag inclusions, cracks, etc. Defects. This article mainly introduces the main reasons and preventive measures for porosity in submerged arc welding seams. (1) In the process of steel rolling or hot stamping and coiling, the oxide scale formed or fallen off, as well as the positioning welding slag shell, the carbon arc gas created flying slag, etc., are trapped in the flux, which will also cause pores in the weld. Preventive measures: ①The oxide skin that falls off during the process of coiling and bending should be cleaned or blown off with compressed air before assembly and welding to prevent it from being caught in the assembly gap or falling into the groove. ②The surrounding of the welding site should be clean t...
阅读全文

Standard for Choosing Oil Casing Pipe Manufacturers

 　　There are many standards for selecting oil casing manufacturers, which can be divided into short-term standards and long-term standards according to the length of time. The short-term standards for selecting oil casing manufacturers mainly include product quality, price level, timely delivery and overall service level. 　　1. Product quality 　　The quality of the purchased oil casing meets the requirements of the purchasing unit is a condition that the purchasing unit must consider when purchasing the oil casing. Poor quality and low price casing products have lower procurement costs, but will lead to an increase in the total cost, but if the quality is too high, it will far exceed the production requirements, which is also a waste. Therefore, the quality requirements of the oil casing in the procurement The production needs of the enterprise must be consistent, and the requirements are too high or too low are not appropriate. 　　2. Lower cost 　　A lower purchase price is an importan...
阅读全文

How to distinguish between ERW steel tube and seamless steel tube?

　　Today, Great Steel Pipe will tell you how to distinguish the ERW steel pipe and seamless steel pipe. 　　 ERW Steel Pipe 　　ERW is a specific type of welding process that is used to produce welded steel pipe, such as ERW steel pipe. Seam welding is commonly used during the manufacturing of round, square and rectangular steel tubing. The steel strip is unwound from coils and side-trimmed to control width and condition the edges for welding. The strip then passes through a series of contoured rollers which cold-form the material into a circular (square or rectangular) shape. The edges are forced together under pressure as a butt joint and then welded by heating the material to temperatures above 2000° F. The flash weld that has formed is now removed from the outside diameter of the tube. Once the weld has been tested the tube then passes through a series of sizing rolls to attain its precise finished size, after which the tube is then straightened and cut to length. 　 　Seamless Ste...
阅读全文